AWG to mm² (Cross-Sectional Area) Conversion
Short answer: Look up your AWG value in the reference table below to find the equivalent conductor area in square millimetres (mm²). Common Australian cable sizes are highlighted further down. For stranded wire, use our stranded wire calculator instead.
While diameter is what you measure physically, cross-sectional area (mm²) is what determines current-carrying capacity, voltage drop and electrical resistance. Australian cable is commonly specified in mm² rather than AWG, so this conversion is essential when comparing imported cable to local equivalents.
AWG to mm² Reference Table
Use the table below as a quick reference to find the American Wire Gauge (AWG) value for a known conductor cross-sectional area in square millimetres (mm²), or vice versa.
| Conductor Area (mm²) | AWG Value | Conductor Area (mm²) | AWG Value | Conductor Area (mm²) | AWG Value | Conductor Area (mm²) | AWG Value |
|---|---|---|---|---|---|---|---|
| 135.10 | 5/0 | 10.60 | 7 | 0.823 | 18 | 0.0646 | 29 |
| 107.20 | 4/0 | 8.35 | 8 | 0.653 | 19 | 0.0503 | 30 |
| 85.00 | 3/0 | 6.62 | 9 | 0.519 | 20 | 0.0400 | 31 |
| 67.50 | 2/0 | 5.27 | 10 | 0.412 | 21 | 0.0320 | 32 |
| 53.40 | 0 | 4.15 | 11 | 0.325 | 22 | 0.0252 | 33 |
| 42.40 | 1 | 3.31 | 12 | 0.259 | 23 | 0.0200 | 34 |
| 33.60 | 2 | 2.63 | 13 | 0.205 | 24 | 0.0161 | 35 |
| 26.70 | 3 | 2.08 | 14 | 0.163 | 25 | 0.0123 | 36 |
| 21.20 | 4 | 1.65 | 15 | 0.128 | 26 | 0.0100 | 37 |
| 16.80 | 5 | 1.31 | 16 | 0.102 | 27 | 0.00795 | 38 |
| 13.30 | 6 | 1.04 | 17 | 0.0804 | 28 | 0.00632 | 39 |
Common Cable AWG to mm² Conversions
The most frequent conversions Australian installers need:
| Cable Type | AWG | Area (mm²) |
|---|---|---|
| Cat5e network cable | 24 AWG | 0.205 mm² |
| Cat6 / Cat6A network cable | 23 AWG | 0.259 mm² |
| Telephone wire | 22 AWG | 0.325 mm² |
| Speaker cable (light) | 18 AWG | 0.823 mm² |
| Speaker cable (heavy) | 14 AWG | 2.08 mm² |
| Mains power cord | 14-12 AWG | 2.08-3.31 mm² |
Why mm² Matters for Cable Selection
Cross-sectional area determines a cable's electrical capacity in ways that diameter alone doesn't capture. Specifically:
- Current-carrying capacity: Australian standard AS/NZS 3008 specifies maximum current ratings based on conductor area in mm²
- Voltage drop: Critical for PoE installs, where insufficient area causes camera or AP failures over long runs
- Resistance: Lower area = higher resistance per metre
- Compliance: Australian electrical regulations reference mm² for installations covered by AS/NZS 3000
Related Calculators & References
- AWG Overview - understand the AWG system and conversion basics
- AWG Calculator by Diameter - find AWG from a known diameter in mm
- AWG Calculator for Stranded Wire - equivalent AWG for stranded conductors
- How to Calculate Cable Area - step-by-step area formulas
- How to Calculate Cable Diameter - find overall diameter of stranded cable
- AWG Reference Table - complete specs including weight and DC resistance
Frequently Asked Questions
How do I convert AWG to mm²?
Look up the AWG value in the reference table above to find the equivalent cross-sectional area in mm². For example, 14 AWG = 2.08 mm², and 24 AWG = 0.205 mm².
What is 14 AWG in mm²?
14 AWG wire has a cross-sectional area of 2.08 mm². This is commonly used for heavy-duty speaker cable and mains power leads.
What is 18 AWG in mm²?
18 AWG wire has a cross-sectional area of 0.823 mm². Common for low-voltage lighting and light-duty audio.
What is 22 AWG in mm²?
22 AWG wire has a cross-sectional area of 0.325 mm². Common in security and alarm cable.
What is 24 AWG in mm²?
24 AWG wire has a cross-sectional area of 0.205 mm². Standard for Cat5e network cable conductors.
Why does Australian cable use mm² instead of AWG?
Australia officially uses the metric system, and AS/NZS 3008 specifies current-carrying capacity based on mm² conductor area. Most networking and imported cable is specified in AWG, so Australian installers need to convert between the two.
Is mm² the same as cross-sectional area?
Yes. mm² (square millimetres) is the unit used to measure cross-sectional area of a conductor. It's the surface area you'd see if you cut the wire perpendicular to its length.
How does cross-sectional area relate to wire diameter?
Area = π × (Diameter/2)². For example, a 1mm diameter wire has an area of 0.785 mm². See our cable area calculator for the formula and worked examples.
Your Project, Perfected. That's The Access Advantage.
- Expert Local Support, Since 1973: Don't waste time with guesswork. Our experts have seen it all and are ready to provide the right solution, right now. Your success is our business.
- Uncompromising Aussie Quality: We live and breathe quality. From rigorous testing to official Australian certification, we guarantee every product we sell is built to perform and built to last.
- Your Specs, Your Brand, Our Build: Off-the-shelf not cutting it? We specialise in building custom cables and assemblies to your exact specifications, branded for your business. Let's create it together.
- Guaranteed for Life: Buy it once. Trust it forever. Our products are backed by a limited lifetime warranty, so you can invest in quality with zero risk. *Warranty excludes third-party brands such as HALO and UPS.
- Innovation That Keeps You Ahead: The tech landscape is always changing, and so is our catalogue. We ensure you always have access to the latest, most reliable solutions on the market.
Let's get your project started.
Talk to an expert today for a custom quote or browse the solutions most relevant to your search.